Remove Ceramic Coating High Spots and Prep With One Spray

Reborn surface prep spray misting onto a black car panel

A high spot is a patch of ceramic coating that didn’t level out before it flashed, and once it cures it’s a real headache to fix. Catch it early and a little Reborn on a clean towel wipes it flat. Reborn is also the final prep spray you use before you coat, so one bottle handles both ends of the job: prep before, rescue after.

What is a high spot in ceramic coating?

If you’ve ever applied a ceramic coating, you know how easy it is to leave behind a high spot. It’s an uneven patch of coating that doesn’t level out, so it sits thicker than the coating around it. Once it cures, it can be a real headache to fix.

That’s where Reborn comes in.

Reborn is a ready-to-use panel prep spray made to clean and correct. Catch a high spot early enough, and a little Reborn on a clean microfiber towel can break it down and give you a second chance to level it out properly. It’s fast, and it saves you from redoing an entire panel.

Gloved hand spraying Fireball Reborn prep spray on a black car

How to remove ceramic coating high spots before they cure

  1. Check every panel under bright light right after you level the coating.
  2. Spray Reborn onto a clean edgeless microfiber towel, not straight onto the panel.
  3. Wipe the high spot gently until it breaks down and the panel looks even.
  4. Re-coat that spot only if it needs it. A lot of the time it doesn’t.

In one job, a fresh coating on a wheel began to flash unevenly. A couple of sprays of Reborn on a clean edgeless towel wiped the spot flat and left a flawless finish, with no extra polishing required.

Bottle of Fireball Reborn surface prep spray on a black car

Prep with Reborn before you coat

The same spray is the final prep wipe before a ceramic coating goes on. It removes oils, wax, polish residue, grease and silica so the coating bonds to a clean, bare surface on paint, wheels, trim or plastics. Test it on a small, hidden area first, then spray it onto a microfiber towel and wipe evenly.

Coating your own car? Prep with Reborn before Angel Tears II DIY Ceramic Coating or Nano Coat V3 Nano Ceramic Coating. Want it done for you? Find a Fireball installer near you, or learn the full process at the Fireball Training Academy.

Reborn spray bottle next to a freshly misted black panel

More Than Just for Cars

Reborn does more than rescue coating jobs. It’s safe on leather, plastics, vinyl, coated wood, screens and even electronics when used as directed. It’s silicone-free and body-shop safe, so it won’t leave a smeary film behind.

And it smells good, too: a fresh citrus scent.

Why Detailers Keep Reaching for Reborn

  • Removes fresh high spots quickly
  • Cleans without leaving residue
  • Works on nearly any surface, inside or out
  • Easy to use and body-shop safe
  • Smells clean, not chemical
Close-up of Reborn mist on a dark glossy car panel

Ceramic coating high spots: FAQ

It’s a patch of ceramic coating that didn’t level out before it flashed, so it sits thicker than the coating around it. Fresh high spots wipe off. Cured ones are much harder to fix.

Catch it before it cures. Spray Reborn onto a clean microfiber towel and wipe the spot gently until it breaks down and the panel looks even.

Only if it needs it. A lot of the time it doesn’t. Check the spot under good light before you decide.

Work in small sections. Level the coating when small dots start to form, using the same side of the towel, then flip to a clean side to finish. Check each panel under bright light before you move on.

Yes. Reborn is Fireball’s panel prep spray and the final wipe before a ceramic coating, wax, PPF or window tint goes on. Test it on a small, hidden area first, and spray the towel, not the panel.

It’s harder. A cured high spot usually needs a light machine polish on that spot, then a fresh layer of coating there. If you’re not sure, ask a Fireball installer.